Sniper 150 Mxi Modification

[gdeezzyy]

sharing my latest set.
tuneboss ecu
cms t2 cams (5.8mm lift)
57mm dome type forged piston(spec v)
port n polish head

using 14x45 sprocket set(advance reading) rpm was very angry at all gears even at final drive, unfortunately speedo reading stays at 152kph but the rpm was very angry i guess i need to go back to the factory sprocket setting for more top end power.

 

[JapSpeed]

Is the uma 57 mm a semi dome or full done type ?

i think it's semi dome piston..

 

[Wamonoseko]

sharing my latest set.
cms t2 cams (5.8mm lift)
57mm dome type forged piston(spec v)
port n polish head

using 14x45 sprocket set(advance reading) rpm was very angry at all gears even at final drive, unfortunately speedo reading stays at 152kph but the rpm was very angry i guess i need to go back to the factory sprocket setting for more top end power.

Semi dome piston sir already have valve pocket,right? Did you make ur valve pocket more deep sir?or not?

 

[Wamonoseko]

i think it's semi dome piston..

Boss jap,ano pala tamang setting ng cms t2 cam?retard?advance?o tamang timing lang boss?salamat.

 

[gdeezzyy]

Semi dome piston sir already have valve pocket,right? Did you make ur valve pocket more deep sir?or not?

yes sir it has a valve pocket already and i didnt do anything as per sir @JapSpeed advice not to do more valve pocketing.

 

[Wamonoseko]

yes sir it has a valve pocket already and i didnt do anything as per sir @JapSpeed advice not to do more valve pocketing.

without base gasket sir?how about your valve clearance?ty

 

[gdeezzyy]

without base gasket sir?how about your valve clearance?ty

i did not remove the base gasket sir, valve clearance is currently .10mm intake .20mm exhaust and the sound is tik tik tik tik hahaha! maybe i will try .08mm intake .10mm exhaust on my nxt change oil.

 

[MXKINGLOVER]

Sir i need advice, when i go more 10k RPM at 4th gear my Speed locks on 136 when i shift to 5th gear , but when i shift below 10k RPM my Top speed goes 145 kph. What should i tune on my Aftermarket ecu? My mods is JUKEN3 DUAL band ecu and Mody5 racing exhaust.

 

[gdeezzyy]

need advice regarding back fire/throttle response delay on 4-6k rpm. do i need to install adjustable timing gear? my cam is cms t2.

 

[sprinter777]

need advice regarding back fire/throttle response delay on 4-6k rpm. do i need to install adjustable timing gear? my cam is cms t2.

maybe you have air leak in your exhaust system or your A/F setting at low speed (IDLE) too lean..,adjust your ignition timing for additional response..

 

[sprinter777]

sharing my current Mx king project..

 

[Richard M. Pabelona Jr.]

May I ask if what's the ideal camshaft for pitsbike v1 ecu for Sniper 150?
Planning to use aftermarket camshaft with pitsbike ecu on a stock bore, valve, etc..
Thanks

 

[Wamonoseko]

May I ask if what's the ideal camshaft for pitsbike v1 ecu for Sniper 150?
Planning to use aftermarket camshaft with pitsbike ecu on a stock bore, valve, etc..
Thanks

Z5 5.7mm boss,better acceleration and top,

 

[Richard M. Pabelona Jr.]

Z5 5.7mm boss,better acceleration and top,

Thanks sir! any ideas where to get or order? I'm from Bacolod City, Negros Occidental. Perhaps some members near me who has.. or if not equivalent.
and btw, the mechanic of the previous owner of my king said that it had its piston pocketed already..what camshaft will I use to take advantage of the pocket? thanks a lot!

 

[gdeezzyy]

what's the best timing for the cms t2 cams? angle maybe? thanks

 

[Kenshin18]

Hello papa jap..im newbie here! I just want ti know the good modification of my sniper 150mxi.. I want to increase the power of my king..any good suggestion and tested modification...All stock

 

[Kenshin18]

Sir jap 13/42 ba magandang sprocket for my stock king? thanks for the advance reply

 

[Kenshin18]

sir japs this is the modification that give me with chaz ortiz

 

[Kenshin18]

 

[JapSpeed]

Sir jap 13/42 ba magandang sprocket for my stock king? thanks for the advance reply

yes, but your speedo reading is not accurate, real top speed is less than 130kph.